They work only in drawing mode (= not live, click on drawing board to focus).

• a: add straight path
• b: add bezier path
• m: modify path
• z: delete the last endpoint of the currently selected robot
• ctrl + a: select all endpoints
• ctrl + c: copy selected endpoints
• ctrl + v: paste copied endpoints
• ctrl + s: save

Select an action to start drawing. (either or )

Start drawing from dock:
select a robot
and drag from the dock

Extend path:
drag from the last endpoint

Modify path:
possible when drawing, all except the last EP. Left click + drag an endpoint to a new position

Context menu and deleting an EP:
Right click on EP to open the menu

Bezier curves:
converting a straight line to a curved one
moving the anchor of a bezier curve

Selecting multiple endpoints:

• CTRL + Left click: adds one endpoint to the selection
• CTRL + Left click: adds one or more endpoints, extended from the range of the last selected endpoint
• Shift or CTRL + Right click: paste to coordinates

Selecting EP's:
multiple and single select
clearing selection

WIE VIELE MENSCHEN BESITZEN BITCOINS?

• Grey EP's: Initial position helpers, taken from the last EP from previous scene. Notice that the angle is also indicated by a black arrow.
• Pink borders: simulation results
• Red dots: collision points, indicates a path collision.
  
  When drawing your paths, they are automatically validated by RobotControl after each modification (unless the auto validation and simulation checkbox is unchecked). Collisions will result in an "invalid path" error. These are shown by red dots on the canvas.
  There are two types of collisions.
  • Obstacle collisions: the path crosses an obstacle or goes outside of the grid bounds. Avoid this by altering the path.
  • Robot collisions: the path of multiple robots crosses and two robots are at or near the same spot at the same time. Avoid this by delaying a robot or altering the path.
  Avoiding collisions:
  make sure your scenario doesn't contain collisions!

BITCOIN KAUFEN

• Red borders: an erroneous state, an admin will have to intervene.
• Light greenish/blue border: robot is idle and ready to go!
• Orange border: robot is active and executing a scenario.
• Gray border: robot is charging

• Click the live button first (drawing controls will be disabled)
• Via the actions dialog you can pass live action(s) to robot(s)
• You can move the location manually by dragging out from a robot in idle state, use the buttons in the lower left gray box.

• The tildes (

  ~~~~

  ) below the robots status, can change to

  rlzb

  . These letters mean:
  • r: right eye open
  • l: left eye open
  • p: device on top of the robot is powered
  • b: battery on top of the robot is charging
• The text above the tildes indicates the charging state of the robot. This will mostly be

  wait

  , if the robot is not docked.

240 MILLIONEN BITCOIN

Set location (shortcut)

Set orientation (shortcut)

Drag & drive

If a path without errors has been drawn, one can proceed to test it for the first time.

• By default, the robot starts from its safezone. Pressing the Initialize button will put the robot exactly there.
• The button will play the current scene. All robots need to be at their starting positions before they can drive. The scenario will start to run and an estimate of the duration will appear.
• The button will play from the currently selected scene to the end, or, to a scene that does not auto-start.
• Scenes can be added, deleted and swapped. Click and drag to put a scene earier or later. This should be done with care, as a swap can result in collisions.
• Scenes can be doubleclicked for name-changes or right clicked for more options.

Sensor bitmap layout:

• 2 sensors: LyLxRyRx (e.g.

  1001

  if LY (left sensor saw Y line) and RX (right sensor saw X line))
• 4 sensors: s3s2s1s0 (with s = (yx), e.g.:

  00011011

  for no_s3 (saw nothing), s2x (s2 saw X), s1y (s1 saw Y), s0_error (s0 saw both X and Y))

Correction-field layout:

• Should be three fields, separated by a '|', e.g.: 1|2|3 for correction in X = 1 cm, correction in Y = 2 cm and angular correction = 3 degrees.

KOSTENLOSES INSTANT-BITCOIN

DRAW_HOOKS.push(your_function);

VARNAME = 'new-value';

• GRID_OFFSET_X and GRID_OFFSET_Y: an offset value where the helper-gridlines have to originate.
• ROBOT_COLORS: is an array of colors per robotid (0 based, so changing color for robot 3 -> ROBOT_COLORS[3] = '#123456' (HEX-HTML colors)